Setting up GlusterFS Server Volumes
A volume is a logical collection of bricks where each brick is an export directory on a server in the trusted storage pool. Most of the gluster management operations are performed on the volume.
To create a new volume in your storage environment, specify the bricks that comprise the volume. After you have created a new volume, you must start it before attempting to mount it.
Formatting and Mounting Bricks
Creating a Thinly Provisioned Logical Volume
To create a thinly provisioned logical volume, proceed with the following steps:
1. Create a physical volume(PV) by using the pvcreate command.
For example:
`pvcreate --dataalignment 1280K /dev/sdb`
Here, /dev/sdb is a storage device.
Use the correct dataalignment option based on your device.
>**Note**
>
>The device name and the alignment value will vary based on the device you are using.
2. Create a Volume Group (VG) from the PV using the vgcreate command:
For example:
`vgcreate --physicalextentsize 128K gfs_vg /dev/sdb`
It is recommended that only one VG must be created from one storage device.
3. Create a thin-pool using the following commands:
1. Create an LV to serve as the metadata device using the following command:
`lvcreate -L metadev_sz --name metadata_device_name VOLGROUP`
For example:
`lvcreate -L 16776960K --name gfs_pool_meta gfs_vg`
2. Create an LV to serve as the data device using the following command:
`lvcreate -L datadev_sz --name thin_pool VOLGROUP`
For example:
`lvcreate -L 536870400K --name gfs_pool gfs_vg`
3. Create a thin pool from the data LV and the metadata LV using the following command:
`lvconvert --chunksize STRIPE_WIDTH --thinpool VOLGROUP/thin_pool --poolmetadata VOLGROUP/metadata_device_name`
For example:
`lvconvert --chunksize 1280K --thinpool gfs_vg/gfs_pool --poolmetadata gfs_vg/gfs_pool_meta`
>**Note**
>
>By default, the newly provisioned chunks in a thin pool are zeroed to prevent data leaking between different block devices.
`lvchange --zero n VOLGROUP/thin_pool`
For example:
`lvchange --zero n gfs_vg/gfs_pool`
4. Create a thinly provisioned volume from the previously created pool using the lvcreate command:
For example:
`lvcreate -V 1G -T gfs_vg/gfs_pool -n gfs_lv`
It is recommended that only one LV should be created in a thin pool.
Format bricks using the supported XFS configuration, mount the bricks, and verify the bricks are mounted correctly.
1. Run # mkfs.xfs -f -i size=512 -n size=8192 -d su=128K,sw=10 DEVICE to format the bricks to the supported XFS file system format. Here, DEVICE is the thin LV. The inode size is set to 512 bytes to accommodate for the extended attributes used by GlusterFS.
Run # mkdir /mountpoint to create a directory to link the brick to.
Add an entry in /etc/fstab:
`/dev/gfs_vg/gfs_lv /mountpoint xfs rw,inode64,noatime,nouuid 1 2`
Run # mount /mountpoint to mount the brick.
Run the df -h command to verify the brick is successfully mounted:
`# df -h
/dev/gfs_vg/gfs_lv 16G 1.2G 15G 7% /exp1`
-
Volumes of the following types can be created in your storage environment:
-
Distributed - Distributed volumes distributes files throughout the bricks in the volume. You can use distributed volumes where the requirement is to scale storage and the redundancy is either not important or is provided by other hardware/software layers.
-
Replicated – Replicated volumes replicates files across bricks in the volume. You can use replicated volumes in environments where high-availability and high-reliability are critical.
-
Striped – Striped volumes stripes data across bricks in the volume. For best results, you should use striped volumes only in high concurrency environments accessing very large files.
-
Distributed Striped - Distributed striped volumes stripe data across two or more nodes in the cluster. You should use distributed striped volumes where the requirement is to scale storage and in high concurrency environments accessing very large files is critical.
-
Distributed Replicated - Distributed replicated volumes distributes files across replicated bricks in the volume. You can use distributed replicated volumes in environments where the requirement is to scale storage and high-reliability is critical. Distributed replicated volumes also offer improved read performance in most environments.
-
Distributed Striped Replicated – Distributed striped replicated volumes distributes striped data across replicated bricks in the cluster. For best results, you should use distributed striped replicated volumes in highly concurrent environments where parallel access of very large files and performance is critical. In this release, configuration of this volume type is supported only for Map Reduce workloads.
-
Striped Replicated – Striped replicated volumes stripes data across replicated bricks in the cluster. For best results, you should use striped replicated volumes in highly concurrent environments where there is parallel access of very large files and performance is critical. In this release, configuration of this volume type is supported only for Map Reduce workloads.
-
Dispersed - Dispersed volumes are based on erasure codes, providing space-efficient protection against disk or server failures. It stores an encoded fragment of the original file to each brick in a way that only a subset of the fragments is needed to recover the original file. The number of bricks that can be missing without losing access to data is configured by the administrator on volume creation time.
-
Distributed Dispersed - Distributed dispersed volumes distribute files across dispersed subvolumes. This has the same advantages of distribute replicate volumes, but using disperse to store the data into the bricks.
-
To create a new volume
-
Create a new volume :
# gluster volume create [stripe | replica | disperse] [transport tcp | rdma | tcp,rdma]
For example, to create a volume called test-volume consisting of server3:/exp3 and server4:/exp4:
# gluster volume create test-volume server3:/exp3 server4:/exp4 Creation of test-volume has been successful Please start the volume to access data.
Creating Distributed Volumes
In a distributed volumes files are spread randomly across the bricks in the volume. Use distributed volumes where you need to scale storage and redundancy is either not important or is provided by other hardware/software layers.
Note: Disk/server failure in distributed volumes can result in a serious loss of data because directory contents are spread randomly across the bricks in the volume.
To create a distributed volume
-
Create a trusted storage pool.
-
Create the distributed volume:
# gluster volume create [transport tcp | rdma | tcp,rdma]
For example, to create a distributed volume with four storage servers using tcp:
# gluster volume create test-volume server1:/exp1 server2:/exp2 server3:/exp3 server4:/exp4 Creation of test-volume has been successful Please start the volume to access data.
(Optional) You can display the volume information:
# gluster volume info Volume Name: test-volume Type: Distribute Status: Created Number of Bricks: 4 Transport-type: tcp Bricks: Brick1: server1:/exp1 Brick2: server2:/exp2 Brick3: server3:/exp3 Brick4: server4:/exp4
For example, to create a distributed volume with four storage servers over InfiniBand:
# gluster volume create test-volume transport rdma server1:/exp1 server2:/exp2 server3:/exp3 server4:/exp4 Creation of test-volume has been successful Please start the volume to access data.
If the transport type is not specified, tcp is used as the default. You can also set additional options if required, such as auth.allow or auth.reject.
Note: Make sure you start your volumes before you try to mount them or else client operations after the mount will hang.
Creating Replicated Volumes
Replicated volumes create copies of files across multiple bricks in the volume. You can use replicated volumes in environments where high-availability and high-reliability are critical.
Note: The number of bricks should be equal to of the replica count for a replicated volume. To protect against server and disk failures, it is recommended that the bricks of the volume are from different servers.
To create a replicated volume
-
Create a trusted storage pool.
-
Create the replicated volume:
# gluster volume create [replica ] [transport tcp | rdma | tcp,rdma]
For example, to create a replicated volume with two storage servers:
# gluster volume create test-volume replica 2 transport tcp server1:/exp1 server2:/exp2 Creation of test-volume has been successful Please start the volume to access data.
If the transport type is not specified, tcp is used as the default. You can also set additional options if required, such as auth.allow or auth.reject.
Note:
-
Make sure you start your volumes before you try to mount them or else client operations after the mount will hang.
-
GlusterFS will fail to create a replicate volume if more than one brick of a replica set is present on the same peer. For eg. four node replicated volume with a more that one brick of a replica set is present on the same peer. ```
gluster volume create
replica 4 server1:/brick1 server1:/brick2 server2:/brick3 server4:/brick4 volume create:
: failed: Multiple bricks of a replicate volume are present on the same server. This setup is not optimal. Use 'force' at the end of the command if you want to override this behavior.``` Use the
force
option at the end of command if you want to create the volume in this case. -
Arbiter configuration for replica volumes
Arbiter volumes are replica 3 volumes where the 3rd brick acts as the arbiter brick. This configuration has mechanisms that prevent occurrence of split-brains.
It can be created with the following command:
# gluster volume create <VOLNAME> replica 3 arbiter 1 host1:brick1 host2:brick2 host3:brick3
More information about this configuration can be found at Features : afr-arbiter-volumes
Note that the arbiter configuration for replica 3 can be used to create distributed-replicate volumes as well.
Creating Striped Volumes
Striped volumes stripes data across bricks in the volume. For best results, you should use striped volumes only in high concurrency environments accessing very large files.
Note: The number of bricks should be a equal to the stripe count for a striped volume.
To create a striped volume
-
Create a trusted storage pool.
-
Create the striped volume:
# gluster volume create [stripe ] [transport tcp | rdma | tcp,rdma]
For example, to create a striped volume across two storage servers:
# gluster volume create test-volume stripe 2 transport tcp server1:/exp1 server2:/exp2 Creation of test-volume has been successful Please start the volume to access data.
If the transport type is not specified, tcp is used as the default. You can also set additional options if required, such as auth.allow or auth.reject.
Note: Make sure you start your volumes before you try to mount them or else client operations after the mount will hang.
Creating Distributed Striped Volumes
Distributed striped volumes stripes files across two or more nodes in the cluster. For best results, you should use distributed striped volumes where the requirement is to scale storage and in high concurrency environments accessing very large files is critical.
Note: The number of bricks should be a multiple of the stripe count for a distributed striped volume.
To create a distributed striped volume
-
Create a trusted storage pool.
-
Create the distributed striped volume:
# gluster volume create [stripe ] [transport tcp | rdma | tcp,rdma]
For example, to create a distributed striped volume across eight storage servers:
# gluster volume create test-volume stripe 4 transport tcp server1:/exp1 server2:/exp2 server3:/exp3 server4:/exp4 server5:/exp5 server6:/exp6 server7:/exp7 server8:/exp8 Creation of test-volume has been successful Please start the volume to access data.
If the transport type is not specified, tcp is used as the default. You can also set additional options if required, such as auth.allow or auth.reject.
Note: Make sure you start your volumes before you try to mount them or else client operations after the mount will hang.
Creating Distributed Replicated Volumes
Distributes files across replicated bricks in the volume. You can use distributed replicated volumes in environments where the requirement is to scale storage and high-reliability is critical. Distributed replicated volumes also offer improved read performance in most environments.
Note: The number of bricks should be a multiple of the replica count for a distributed replicated volume. Also, the order in which bricks are specified has a great effect on data protection. Each replica_count consecutive bricks in the list you give will form a replica set, with all replica sets combined into a volume-wide distribute set. To make sure that replica-set members are not placed on the same node, list the first brick on every server, then the second brick on every server in the same order, and so on.
To create a distributed replicated volume
-
Create a trusted storage pool.
-
Create the distributed replicated volume:
# gluster volume create [replica ] [transport tcp | rdma | tcp,rdma]
For example, four node distributed (replicated) volume with a two-way mirror:
# gluster volume create test-volume replica 2 transport tcp server1:/exp1 server2:/exp2 server3:/exp3 server4:/exp4 Creation of test-volume has been successful Please start the volume to access data.
For example, to create a six node distributed (replicated) volume with a two-way mirror:
# gluster volume create test-volume replica 2 transport tcp server1:/exp1 server2:/exp2 server3:/exp3 server4:/exp4 server5:/exp5 server6:/exp6 Creation of test-volume has been successful Please start the volume to access data.
If the transport type is not specified, tcp is used as the default. You can also set additional options if required, such as auth.allow or auth.reject.
Note: - Make sure you start your volumes before you try to mount them or else client operations after the mount will hang.
- GlusterFS will fail to create a distribute replicate volume if more than one brick of a replica set is present on the same peer. For eg. four node distribute (replicated) volume with a more than one brick of a replica set is present on the same peer. ```
gluster volume create
replica 2 server1:/brick1 server1:/brick2 server2:/brick3 server4:/brick4 volume create:
: failed: Multiple bricks of a replicate volume are present on the same server. This setup is not optimal. Use 'force' at the end of the command if you want to override this behavior.``` Use the
force
option at the end of command if you want to create the volume in this case.
Creating Distributed Striped Replicated Volumes
Distributed striped replicated volumes distributes striped data across replicated bricks in the cluster. For best results, you should use distributed striped replicated volumes in highly concurrent environments where parallel access of very large files and performance is critical. In this release, configuration of this volume type is supported only for Map Reduce workloads.
Note: The number of bricks should be a multiples of number of stripe count and replica count for a distributed striped replicated volume.
To create a distributed striped replicated volume
-
Create a trusted storage pool.
-
Create a distributed striped replicated volume using the following command:
# gluster volume create [stripe ] [replica ] [transport tcp | rdma | tcp,rdma]
For example, to create a distributed replicated striped volume across eight storage servers:
# gluster volume create test-volume stripe 2 replica 2 transport tcp server1:/exp1 server2:/exp2 server3:/exp3 server4:/exp4 server5:/exp5 server6:/exp6 server7:/exp7 server8:/exp8 Creation of test-volume has been successful Please start the volume to access data.
If the transport type is not specified, tcp is used as the default. You can also set additional options if required, such as auth.allow or auth.reject.
Note: - Make sure you start your volumes before you try to mount them or else client operations after the mount will hang.
- GlusterFS will fail to create a distribute replicate volume if more than one brick of a replica set is present on the same peer. For eg. four node distribute (replicated) volume with a more than one brick of a replica set is present on the same peer. ```
gluster volume create
stripe 2 replica 2 server1:/brick1 server1:/brick2 server2:/brick3 server4:/brick4 volume create:
: failed: Multiple bricks of a replicate volume are present on the same server. This setup is not optimal. Use 'force' at the end of the command if you want to override this behavior.``` Use the
force
option at the end of command if you want to create the volume in this case.
Creating Striped Replicated Volumes
Striped replicated volumes stripes data across replicated bricks in the cluster. For best results, you should use striped replicated volumes in highly concurrent environments where there is parallel access of very large files and performance is critical. In this release, configuration of this volume type is supported only for Map Reduce workloads.
Note: The number of bricks should be a multiple of the replicate count and stripe count for a striped replicated volume.
To create a striped replicated volume
-
Create a trusted storage pool consisting of the storage servers that will comprise the volume.
-
Create a striped replicated volume :
# gluster volume create [stripe ] [replica ] [transport tcp | rdma | tcp,rdma]
For example, to create a striped replicated volume across four storage servers:
# gluster volume create test-volume stripe 2 replica 2 transport tcp server1:/exp1 server2:/exp2 server3:/exp3 server4:/exp4 Creation of test-volume has been successful Please start the volume to access data.
To create a striped replicated volume across six storage servers:
# gluster volume create test-volume stripe 3 replica 2 transport tcp server1:/exp1 server2:/exp2 server3:/exp3 server4:/exp4 server5:/exp5 server6:/exp6 Creation of test-volume has been successful Please start the volume to access data.
If the transport type is not specified, tcp is used as the default. You can also set additional options if required, such as auth.allow or auth.reject.
Note: - Make sure you start your volumes before you try to mount them or else client operations after the mount will hang.
- GlusterFS will fail to create a distribute replicate volume if more than one brick of a replica set is present on the same peer. For eg. four node distribute (replicated) volume with a more than one brick of replica set is present on the same peer. ```
gluster volume create
stripe 2 replica 2 server1:/brick1 server1:/brick2 server2:/brick3 server4:/brick4 volume create:
: failed: Multiple bricks of a replicate volume are present on the same server. This setup is not optimal. Use force
at the end of the command if you want to override this behavior.```Use the
force
option at the end of command if you want to create the volume in this case.
Creating Dispersed Volumes
Dispersed volumes are based on erasure codes. It stripes the encoded data of files, with some redundancy addedd, across multiple bricks in the volume. You can use dispersed volumes to have a configurable level of reliability with a minimum space waste.
Redundancy
Each dispersed volume has a redundancy value defined when the volume is created. This value determines how many bricks can be lost without interrupting the operation of the volume. It also determines the amount of usable space of the volume using this formula:
<Usable size> = <Brick size> * (#Bricks - Redundancy)
All bricks of a disperse set should have the same capacity otherwise, when the smaller brick becomes full, no additional data will be allowed in the disperse set.
It's important to note that a configuration with 3 bricks and redundancy 1 will have less usable space (66.7% of the total physical space) than a configuration with 10 bricks and redundancy 1 (90%). However the first one will be safer than the second one (roughly the probability of failure of the second configuration if more than 4.5 times bigger than the first one).
For example, a dispersed volume composed by 6 bricks of 4TB and a redundancy of 2 will be completely operational even with two bricks inaccessible. However a third inaccessible brick will bring the volume down because it won't be possible to read or write to it. The usable space of the volume will be equal to 16TB.
The implementation of erasure codes in GlusterFS limits the redundancy to a value smaller than #Bricks / 2 (or equivalently, redundancy * 2 < #Bricks). Having a redundancy equal to half of the number of bricks would be almost equivalent to a replica-2 volume, and probably a replicated volume will perform better in this case.
Optimal volumes
One of the worst things erasure codes have in terms of performance is the RMW (Read-Modify-Write) cycle. Erasure codes operate in blocks of a certain size and it cannot work with smaller ones. This means that if a user issues a write of a portion of a file that doesn't fill a full block, it needs to read the remaining portion from the current contents of the file, merge them, compute the updated encoded block and, finally, writing the resulting data.
This adds latency, reducing performance when this happens. Some GlusterFS performance xlators can help to reduce or even eliminate this problem for some workloads, but it should be taken into account when using dispersed volumes for a specific use case.
Current implementation of dispersed volumes use blocks of a size that depends on the number of bricks and redundancy: 512 * (#Bricks - redundancy) bytes. This value is also known as the stripe size.
Using combinations of #Bricks/redundancy that give a power of two for the stripe size will make the disperse volume perform better in most workloads because it's more typical to write information in blocks that are multiple of two (for example databases, virtual machines and many applications).
These combinations are considered optimal.
For example, a configuration with 6 bricks and redundancy 2 will have a stripe size of 512 * (6 - 2) = 2048 bytes, so it's considered optimal. A configuration with 7 bricks and redundancy 2 would have a stripe size of 2560 bytes, needing a RMW cycle for many writes (of course this always depends on the use case).
To create a dispersed volume
-
Create a trusted storage pool.
-
Create the dispersed volume:
# gluster volume create [disperse [<count>]] [redundancy <count>] [transport tcp | rdma | tcp,rdma]
A dispersed volume can be created by specifying the number of bricks in a disperse set, by specifying the number of redundancy bricks, or both.
If disperse is not specified, or the <count> is missing, the entire volume will be treated as a single disperse set composed by all bricks enumerated in the command line.
If redundancy is not specified, it is computed automatically to be the optimal value. If this value does not exist, it's assumed to be '1' and a warning message is shown:
# gluster volume create test-volume disperse 4 server{1..4}:/bricks/test-volume There isn't an optimal redundancy value for this configuration. Do you want to create the volume with redundancy 1 ? (y/n)
In all cases where redundancy is automatically computed and it's not equal to '1', a warning message is displayed:
# gluster volume create test-volume disperse 6 server{1..6}:/bricks/test-volume The optimal redundancy for this configuration is 2. Do you want to create the volume with this value ? (y/n)
redundancy must be greater than 0, and the total number of bricks must be greater than 2 * redundancy. This means that a dispersed volume must have a minimum of 3 bricks.
If the transport type is not specified, tcp is used as the default. You can also set additional options if required, like in the other volume types.
Note:
-
Make sure you start your volumes before you try to mount them or else client operations after the mount will hang.
-
GlusterFS will fail to create a dispersed volume if more than one brick of a disperse set is present on the same peer.
```
gluster volume create
disperse 3 server1:/brick{1..3} volume create:
: failed: Multiple bricks of a replicate volume are present on the same server. This setup is not optimal. Do you still want to continue creating the volume? (y/n)``` Use the
force
option at the end of command if you want to create the volume in this case. -
Creating Distributed Dispersed Volumes
Distributed dispersed volumes are the equivalent to distributed replicated volumes, but using dispersed subvolumes instead of replicated ones.
To create a distributed dispersed volume
-
Create a trusted storage pool.
-
Create the distributed dispersed volume:
# gluster volume create disperse <count> [redundancy <count>] [transport tcp | rdma | tcp,rdma]
To create a distributed dispersed volume, the disperse keyword and <count> is mandatory, and the number of bricks specified in the command line must must be a multiple of the disperse count.
redundancy is exactly the same as in the dispersed volume.
If the transport type is not specified, tcp is used as the default. You can also set additional options if required, like in the other volume types.
Note:
-
Make sure you start your volumes before you try to mount them or else client operations after the mount will hang.
-
GlusterFS will fail to create a distributed dispersed volume if more than one brick of a disperse set is present on the same peer.
```
gluster volume create
disperse 3 server1:/brick{1..6} volume create:
: failed: Multiple bricks of a replicate volume are present on the same server. This setup is not optimal. Do you still want to continue creating the volume? (y/n)``` Use the
force
option at the end of command if you want to create the volume in this case. -
Starting Volumes
You must start your volumes before you try to mount them.
To start a volume
-
Start a volume:
# gluster volume start
For example, to start test-volume:
# gluster volume start test-volume Starting test-volume has been successful